PDA

View Full Version : Vintage Aurora 88 Tear-down



dannzeman
April 17th, 2010, 03:57 PM
The Aurora 88 has quickly become one of my favorite pens, both the modern and vintage designs. After using a friend’s vintage 88 and experiencing its’ wonderful flex I added several to my collection and began to repair and sell several others. Here I’ll present the pen in its various pieces and what you should look out for should you try to take one apart.

http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-32-480x87.jpg (http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-32.jpg)

http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-4-labeled-480x38.jpg (http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-4-labeled.jpg)

http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-23-480x101.jpg (http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-23.jpg)

http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-6-480x84.jpg (http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-6.jpg)

One of the few reasons to remove a feed is if a pen has poor or inconsistent flow. I rarely experience flow problems with these pens and this was actually the first time I needed to remove the feed. If the feed must be removed it can be pushed out the front of the section. The feed is not keyed to the section in any way so you must keep it from rotating off center when inserting it back into the section. Once the feed is pushed into the section by hand there is a ledge molded into the feed where a slotted screw driver can be used to push the feed the rest of the way into the section (shown by the next two pictures). The nib should easily slide onto the feed once the feed is securely in the section. Thankfully, the nib can’t be rotated off center like on the Parker “51″.

http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-31-480x330.jpg (http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-31.jpg)

http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-30-480x324.jpg (http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-30.jpg)

http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-9-label-480x152.jpg (http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-9-label.jpg)
The piston unit (above) consists of the piston shaft, piston seal, and the nut that holds the seal on the shaft. The hexagonal shape of the shaft slides inside a hexagonal cylinder in the barrel to prevent the piston from rotating during a filling cycle. The inside of the piston shaft is threaded to mate with the piston screw (shown below). The piston screw remains stationary while rotated which causes the piston shaft to move inside the barrel. If the pen has poor suction the seal will need to be replaced. I like to use “c” sized piston seals from VintagePens.com (http://www.vintagepens.com/catill_nibs_parts.shtml). Make sure you lightly apply some silicone lube to the seals to keep them from squeaking inside the barrel.

http://www.dannzeman.com/wp-content/uploads/2010/01/untitled-480x172.jpg (http://www.dannzeman.com/wp-content/uploads/2010/01/untitled.jpg)

http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-12-480x123.jpg (http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-12.jpg)
The picture above shows the piston screw and is somewhat inaccurate in that there’s no way to remove the piston screw with the aluminum collar still attached. The pin holding the collar onto the piston screw must be knocked out and then the collar can be removed and the piston screw can be pushed out of the other end of the barrel.

http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-piston-screw-collar-480x243.jpg (http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-piston-screw-collar.jpg)
Finally, the piston knob slides over the collar and is keyed to piston screw. The piston knob is secured to the piston screw by a small slotted screw with a spring on it. Most 88s will have a small plastic insert in the piston knob that covers the screw which requires an exacto knife to remove.

http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-5-480x72.jpg (http://www.dannzeman.com/wp-content/uploads/2010/01/Aurora-88-parts-5.jpg)






If you would like to read more fountain pen related articles please check out my blog athttp://dannzeman.com (http://dannzeman.com/)

eriquito
April 18th, 2010, 10:37 AM
Gorgeous tear-down dannzeman!

For all of us vintage 88 fans, this explains A LOT!

Thank you! =)

Eric
Son of Ragnar

Okami
April 18th, 2010, 10:45 AM
;)I'm still waiting for you to post a vintage 88 with flex that I can afford - wonderful description of this pen and the work involved in restoring one. Thanks for the insight

SProctor
April 18th, 2010, 01:49 PM
Very well thought out and instituted, thank so much! This is such a great pen to have this on too... Great Job!

Very Best Wishes,

Stephen P.

dannzeman
April 19th, 2010, 11:51 AM
;)I'm still waiting for you to post a vintage 88 with flex that I can afford
It might be a while. I haven't received any 88s in a long time.

Sent from my HERO200 using Tapatalk

Wile E Coyote
April 19th, 2010, 01:07 PM
;)I'm still waiting for you to post a vintage 88 with flex that I can afford

Me too.

ttakacs
August 20th, 2010, 11:54 AM
Can the nib be removed without removing the section?

dannzeman
August 20th, 2010, 05:24 PM
Can the nib be removed without removing the section?

On some pens it is possible to grab the nib and pull it out without removing the section. On others, it's not possible. At least not without using pliers or something to grip the nib with, which I don't recommend doing because it's easy to break the tipping off the nib.

ttakacs
August 27th, 2010, 07:49 PM
That was so helpful. I was able to wriggle out the old nib by using my fingers and some patience. I inserted the replacement nib simply by pushing it in as far as it would go. Inked the pen and started writing.

Sagebrush64
June 3rd, 2017, 08:33 PM
Any chance this can be reposted with pictures...seems Danzzeman's server is no longer active.