Results 1 to 6 of 6

Thread: Parker 51, setting hood to nib, (How much nib should be visable)

  1. #1
    Senior Member
    Join Date
    May 2013
    Location
    Kent UK
    Posts
    548
    Thanks
    25
    Thanked 172 Times in 90 Posts
    Rep Power
    7

    Default Parker 51, setting hood to nib, (How much nib should be visable)

    Hi all

    Hopefuĺly a quick question

    With aĺl the Parker 51's I have seen the hood is set so that only the tipping of the nib is visible, and on most after stripling the hood, nib, feed goes back fine with only the tipping showing. But on a few I have at the moment, although the feed is fully inserted as is the nib, once the hood is fully seated there is far too much nib visible, so this got me wondering if the hood should be fully seated to the clutch ring or was the hood originally set to the nib position and fixed in place by the thread sealant.

    These are ones that have the o-ring so doing that can leave a small gap between the base off the hood and clutch ring.

    Other than that is there any other obvious reason why the nib should stick out more after reassembly than before. As said the nib and feed are fully inserted in the collector.

    Thanks for any help with this and sorry it went on a bit more than I hoped.

    Paul

  2. #2
    Senior Member FredRydr's Avatar
    Join Date
    Sep 2012
    Location
    Carlisle, Pennsylvania USA
    Posts
    2,559
    Thanks
    514
    Thanked 2,575 Times in 1,094 Posts
    Rep Power
    11

    Default Re: Parker 51, setting hood to nib, (How much nib should be visable)

    Most nibs I've had and seen are set as you describe. One exception I own is this factory stub nib, which only flowed well when positioned as shown in the photo.

    IMG_1894.jpg

  3. #3
    FPG Donor ♕ Chrissy's Avatar
    Join Date
    Dec 2013
    Location
    Berkshire UK
    Posts
    5,443
    Thanks
    2,507
    Thanked 4,570 Times in 1,761 Posts
    Rep Power
    12

    Default Re: Parker 51, setting hood to nib, (How much nib should be visable)

    Mine were always sticking out a bit more than just the tipping, and they were all fine to write with. if the tipping is right at the point of the hood, then the point might rub on the Iridium and become damaged.
    I always aimed for a natural extension of the curve of the feed into the hood at the back
    Regards, Chrissy | My Blog: inkyfountainpens

  4. #4
    Senior Member
    Join Date
    Oct 2012
    Posts
    545
    Thanks
    41
    Thanked 231 Times in 111 Posts
    Rep Power
    8

    Default Re: Parker 51, setting hood to nib, (How much nib should be visable)

    Maybe the collector isn't fully seated.

    --Daniel
    “Every discussion which is made from an egoistic standpoint is corrupted from the start and cannot yield an absolutely sure conclusion. The ego puts its own interest first and twists every argument, word, even fact to suit that interest.”
    ― Paul Brunton, The Notebooks of Paul Brunton

  5. #5
    Senior Member
    Join Date
    May 2013
    Location
    Kent UK
    Posts
    548
    Thanks
    25
    Thanked 172 Times in 90 Posts
    Rep Power
    7

    Default Re: Parker 51, setting hood to nib, (How much nib should be visable)

    Yes the collector is fully seated, I can see and feel it hit the bottom of its socket. Just looks to me like the hood is screwing on to far, which made me think it was screwed and then glued (sealed) to the nib position rather than than just screwed fully home worth the nib position adjusted to the hoods orientation.

    Not had this issue before but the last 10 or so have all been like it.

    They all work fine, it just looks odd with so much nib exposed.

    Paul

  6. #6
    Senior Member azkid's Avatar
    Join Date
    Mar 2018
    Location
    Colorado, USA
    Posts
    1,306
    Thanks
    2,200
    Thanked 1,065 Times in 503 Posts
    Rep Power
    3

    Default Re: Parker 51, setting hood to nib, (How much nib should be visable)

    Quote Originally Posted by Paul-H View Post
    Yes the collector is fully seated, I can see and feel it hit the bottom of its socket. Just looks to me like the hood is screwing on to far, which made me think it was screwed and then glued (sealed) to the nib position rather than than just screwed fully home worth the nib position adjusted to the hoods orientation.
    I have only ever had a Parker 21 apart once but I fixed the hood position to the nib.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •