Results 1 to 19 of 19

Thread: Doing my first pen re-sacking

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Senior Member southpaw52's Avatar
    Join Date
    Apr 2010
    Location
    Fort Smith AR
    Posts
    859
    Thanks
    450
    Thanked 231 Times in 141 Posts
    Rep Power
    14

    Default Doing my first pen re-sacking

    Couple of questions regard pen re sacking;

    Which type of sacks work the best latex or silicone?

    Do you measure the sack according to the barrel length, then cut off the excess?

    What is recommended for bringing back luster to a pen?

    What basic tools are needed to re-sack?

    Lastly any other advice?

    Thanks in advance.


    InCoWri 2018, Letter Writers Alliance Member, Postable link: www.postable.com/bradharris, postcrossing

  2. #2
    Senior Member Sailor Kenshin's Avatar
    Join Date
    Apr 2012
    Location
    Where pigs run free!
    Posts
    4,003
    Thanks
    6,231
    Thanked 3,423 Times in 1,715 Posts
    Rep Power
    17

    Default Re: Doing my first pen re-sacking

    Quote Originally Posted by southpaw52 View Post
    Couple of questions regard pen re sacking;

    Which type of sacks work the best latex or silicone?

    Do you measure the sack according to the barrel length, then cut off the excess?

    What is recommended for bringing back luster to a pen?

    What basic tools are needed to re-sack?

    Lastly any other advice?

    Thanks in advance.
    What kind of pen are you re-saccing? There's a standard list of sizes....and the kind of pen will help determine latex or silicone.

    Length can be trimmed as needed. It's the girth you worry about. Will it fit inside the barrel and can the J-bar activate easily? That kind of thing.

    Richard Binder's site is a good starting point.
    My other pen is a Montblanc.

    And my other blog is a tumblr!


    And my latest ebook, for spooky wintery reading:

    https://www.amazon.com/gp/product/B0CM2NGSSD

  3. The Following 2 Users Say Thank You to Sailor Kenshin For This Useful Post:

    Jon Szanto (April 29th, 2019), southpaw52 (May 1st, 2019)

  4. #3
    Senior Member Jon Szanto's Avatar
    Join Date
    Feb 2012
    Posts
    6,616
    Thanks
    7,795
    Thanked 11,039 Times in 4,010 Posts
    Rep Power
    22

    Default Re: Doing my first pen re-sacking

    Quote Originally Posted by Sailor Kenshin View Post
    Richard Binder's site is a good starting point.
    Specifically, read over all the information on his page on How To Replace a Pen Sac.
    "When Men differ in Opinion, both Sides ought equally to have the Advantage of being heard by the Publick;
    and that when Truth and Error have fair Play, the former is always an overmatch for the latter."

    ~ Benjamin Franklin

  5. The Following User Says Thank You to Jon Szanto For This Useful Post:

    southpaw52 (May 1st, 2019)

  6. #4
    Senior Member southpaw52's Avatar
    Join Date
    Apr 2010
    Location
    Fort Smith AR
    Posts
    859
    Thanks
    450
    Thanked 231 Times in 141 Posts
    Rep Power
    14

    Default Re: Doing my first pen re-sacking

    I am replacing Esterbrook, and Waterman Crusader.
    Thanks for the help


    InCoWri 2018, Letter Writers Alliance Member, Postable link: www.postable.com/bradharris, postcrossing

  7. #5
    Senior Member Jon Szanto's Avatar
    Join Date
    Feb 2012
    Posts
    6,616
    Thanks
    7,795
    Thanked 11,039 Times in 4,010 Posts
    Rep Power
    22

    Default Re: Doing my first pen re-sacking

    Quote Originally Posted by southpaw52 View Post
    I am replacing Esterbrook, and Waterman Crusader.
    Thanks for the help
    Do the Estie first, as they are the easiest pens to work on; be careful with the section on the Crusader, which can be a bit more difficult to remove. Both can be done with latex sacs - I reserve the silicone for pens where the celluloid colors will be darkened by the off-gassing of the latex sacs, and I doubt either pen has that issue.
    "When Men differ in Opinion, both Sides ought equally to have the Advantage of being heard by the Publick;
    and that when Truth and Error have fair Play, the former is always an overmatch for the latter."

    ~ Benjamin Franklin

  8. The Following User Says Thank You to Jon Szanto For This Useful Post:

    southpaw52 (May 1st, 2019)

  9. #6
    Senior Member Voiren's Avatar
    Join Date
    Nov 2018
    Location
    London, UK
    Posts
    372
    Thanks
    226
    Thanked 1,112 Times in 237 Posts
    Rep Power
    6

    Default Re: Doing my first pen re-sacking

    Quote Originally Posted by Jon Szanto View Post

    Do the Estie first, as they are the easiest pens to work on; be careful with the section on the Crusader, which can be a bit more difficult to remove. Both can be done with latex sacs - I reserve the silicone for pens where the celluloid colors will be darkened by the off-gassing of the latex sacs, and I doubt either pen has that issue.
    Thanks for the reminder - I just got a Sheaffer Jade Senior needing a new sac, and that's one where I should probably go for silicone. (The colour is very green! The cap has some other issues but it is functional).

    I sometimes put the sac on without shellacking it first to make sure it all fits right (more often when it is one where a couple of different sac sizes seem like they could be right).

    I use my cross-locking tweezers to help put them on at times - they're closed when you do nothing and open when squeezed and can be used as sac spreaders, though they don't hold it open as roundly as some might.

  10. The Following User Says Thank You to Voiren For This Useful Post:

    southpaw52 (May 1st, 2019)

  11. #7
    FPG Donor ♕ Chrissy's Avatar
    Join Date
    Dec 2013
    Location
    United Kingdom
    Posts
    11,404
    Thanks
    6,876
    Thanked 10,362 Times in 3,977 Posts
    Rep Power
    24

    Default Re: Doing my first pen re-sacking

    I started with an Esterbrook sac and it was very easy to do. I've only ever used latex sacs on Esties, a Swan and a few Sheaffer's. I watched several You Tube videos before I started, and it definitely gets easier after the first one.

    Be careful with the heat that you use to help you to free the barrel. Don't get it too hot.

    You will need to cut the sac to the correct length before you glue it on with shellac.

    Some will recommend a sac spreader for helping to get the sac on. I don't have one.
    Regards, Chrissy | My Review Blog: inkyfountainpens

  12. The Following User Says Thank You to Chrissy For This Useful Post:

    southpaw52 (May 1st, 2019)

  13. #8
    Senior Member Deb's Avatar
    Join Date
    Apr 2013
    Location
    Highlands of Scotland
    Posts
    1,747
    Thanks
    2,349
    Thanked 1,927 Times in 842 Posts
    Rep Power
    12

    Default Re: Doing my first pen re-sacking

    Regards,
    Deb
    My Blog

  14. The Following 2 Users Say Thank You to Deb For This Useful Post:

    Chrissy (April 30th, 2019), southpaw52 (May 1st, 2019)

  15. #9
    FPG Donor ♕ Chrissy's Avatar
    Join Date
    Dec 2013
    Location
    United Kingdom
    Posts
    11,404
    Thanks
    6,876
    Thanked 10,362 Times in 3,977 Posts
    Rep Power
    24

    Default Re: Doing my first pen re-sacking

    Thanks Deb, that's very helpful. Of special interest was the dusting of the sac with talc. I watched a TV show the other day where a very well respected restorer replaced a sac in a Wyvern and he did not show this step, although he mentions it in his book.

    I was watching the show with my OH as this pen was being restored and remember saying "don't forget the talc!" as he appeared to replace the sacced section without adding talc to the sac.

    Here is the post where I linked to the TV show in question.
    Last edited by Chrissy; April 30th, 2019 at 04:42 AM.
    Regards, Chrissy | My Review Blog: inkyfountainpens

  16. #10
    Senior Member Deb's Avatar
    Join Date
    Apr 2013
    Location
    Highlands of Scotland
    Posts
    1,747
    Thanks
    2,349
    Thanked 1,927 Times in 842 Posts
    Rep Power
    12

    Default Re: Doing my first pen re-sacking

    Thank you Chrissie. I shall watch that episode with interest!
    Regards,
    Deb
    My Blog

  17. The Following User Says Thank You to Deb For This Useful Post:

    southpaw52 (May 1st, 2019)

  18. #11
    Senior Member
    Join Date
    May 2013
    Posts
    369
    Thanks
    115
    Thanked 247 Times in 125 Posts
    Rep Power
    11

    Default Re: Doing my first pen re-sacking

    The latex sac is generally a better choice than silicone, with the exception of pens that tend to discolor when the latex sac decomposes. The jade celluloid Sheaffer is indeed a good candidate for silicone. When you do a silicone re-sac, be sure you have a silicone sac and not a PVC sac. David Nishimura's website and videos explain the difference.

    My experience is that the re-sac on the lever filler is one of the easier parts. The harder parts include getting the nib/feed properly set and tuned, and properly replacing the J-bar. If you're lucky though you just need to do the re-sac.

  19. The Following User Says Thank You to Ray-VIgo For This Useful Post:

    southpaw52 (May 1st, 2019)

  20. #12
    Senior Member Deb's Avatar
    Join Date
    Apr 2013
    Location
    Highlands of Scotland
    Posts
    1,747
    Thanks
    2,349
    Thanked 1,927 Times in 842 Posts
    Rep Power
    12

    Default Re: Doing my first pen re-sacking

    Quote Originally Posted by Ray-VIgo View Post
    The latex sac is generally a better choice than silicone, with the exception of pens that tend to discolor when the latex sac decomposes.
    I agree with that.
    Regards,
    Deb
    My Blog

  21. The Following User Says Thank You to Deb For This Useful Post:

    southpaw52 (May 1st, 2019)

  22. #13
    Senior Member Deb's Avatar
    Join Date
    Apr 2013
    Location
    Highlands of Scotland
    Posts
    1,747
    Thanks
    2,349
    Thanked 1,927 Times in 842 Posts
    Rep Power
    12

    Default Re: Doing my first pen re-sacking

    I've just watched the episode. No talc! Shocking!

    I pronounce it "Wivern" whereas Laurence pronounces the Y.
    Regards,
    Deb
    My Blog

  23. #14
    Senior Member southpaw52's Avatar
    Join Date
    Apr 2010
    Location
    Fort Smith AR
    Posts
    859
    Thanks
    450
    Thanked 231 Times in 141 Posts
    Rep Power
    14

    Default Re: Doing my first pen re-sacking

    Should the J bar be replaced also?


    InCoWri 2018, Letter Writers Alliance Member, Postable link: www.postable.com/bradharris, postcrossing

  24. #15
    Senior Member
    Join Date
    May 2013
    Posts
    369
    Thanks
    115
    Thanked 247 Times in 125 Posts
    Rep Power
    11

    Default Re: Doing my first pen re-sacking

    Quote Originally Posted by southpaw52 View Post
    Should the J bar be replaced also?
    Only if the lever is loose/rattling when the pen is used, or the old J-bar broke and fell out. If the lever is tight and the old bar is intact, keep it in the pen.

  25. #16
    Senior Member southpaw52's Avatar
    Join Date
    Apr 2010
    Location
    Fort Smith AR
    Posts
    859
    Thanks
    450
    Thanked 231 Times in 141 Posts
    Rep Power
    14

    Default Re: Doing my first pen re-sacking

    I have a Waterman Skywriter, and Crusader what size sac for these pens?


    InCoWri 2018, Letter Writers Alliance Member, Postable link: www.postable.com/bradharris, postcrossing

  26. #17
    Senior Member Jon Szanto's Avatar
    Join Date
    Feb 2012
    Posts
    6,616
    Thanks
    7,795
    Thanked 11,039 Times in 4,010 Posts
    Rep Power
    22

    Default Re: Doing my first pen re-sacking

    Quote Originally Posted by southpaw52 View Post
    I have a Waterman Skywriter, and Crusader what size sac for these pens?
    Go to Richard Binder's site, he has a page that lists many pens and gives their sac sizes along with guidlines for general purpose sac size estimation. It is either on the page on re-saccing pens or a separate page itself.
    "When Men differ in Opinion, both Sides ought equally to have the Advantage of being heard by the Publick;
    and that when Truth and Error have fair Play, the former is always an overmatch for the latter."

    ~ Benjamin Franklin

  27. The Following User Says Thank You to Jon Szanto For This Useful Post:

    azkid (May 10th, 2019)

  28. #18
    FPG Donor ♕ Chrissy's Avatar
    Join Date
    Dec 2013
    Location
    United Kingdom
    Posts
    11,404
    Thanks
    6,876
    Thanked 10,362 Times in 3,977 Posts
    Rep Power
    24

    Default Re: Doing my first pen re-sacking

    I found this thread for the Waterman Skywriter and it also mentions the Crusader
    Regards, Chrissy | My Review Blog: inkyfountainpens

  29. #19
    Senior Member azkid's Avatar
    Join Date
    Mar 2018
    Location
    Colorado, USA
    Posts
    2,016
    Thanks
    3,725
    Thanked 1,703 Times in 822 Posts
    Rep Power
    9

    Default Re: Doing my first pen re-sacking


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •