Results 1 to 12 of 12

Thread: Lever Filler - - How does this work?

  1. #1
    Senior Member
    Join Date
    Aug 2019
    Posts
    100
    Thanks
    51
    Thanked 11 Times in 10 Posts
    Rep Power
    5

    Default Lever Filler - - How does this work?

    I recently bought a nice looking lever Filler but have never used one. Do you put the nib in the ink and then pull up on the lever?
    Thanks. PSX_20190922_140818~2.jpgPSX_20190922_141006~2.jpgPSX_20190922_141359~2.jpg

    Sent from my LG-H910 using Tapatalk

  2. #2
    Senior Member Jon Szanto's Avatar
    Join Date
    Feb 2012
    Posts
    6,605
    Thanks
    7,789
    Thanked 11,015 Times in 4,003 Posts
    Rep Power
    22

    Default Re: Lever Filler - - How does this work?

    Possibly one of the most common vintage purchases, you have an Esterbrook J (which is the largest of their 3 models, though I might be fooled by the photos).

    You can either open the lever before or after putting in the ink but I prefer before; the lever should come out to almost a 90 degree angle to the body. You then dip the pen into the ink and it must come just past the front edge of the section, completely submerging the nib. If you only stick part of the nib in you won't get suction. Once in the ink, release the lever and wait 10 seconds for the sac to fully expand and get a full fill. Remove from ink, wipe the section with a paper towel to get off any excess ink and you are ready to go.

    You'll find a host of info about the pen at the long-running Esterbrook.net site run by Brian Anderson (I've linked to the pages on the J series). Enjoy!
    "When Men differ in Opinion, both Sides ought equally to have the Advantage of being heard by the Publick;
    and that when Truth and Error have fair Play, the former is always an overmatch for the latter."

    ~ Benjamin Franklin

  3. The Following User Says Thank You to Jon Szanto For This Useful Post:

    MTHall720 (September 22nd, 2019)

  4. #3
    Senior Member
    Join Date
    Nov 2016
    Location
    Clinging desperately to planet Earth
    Posts
    474
    Thanks
    36
    Thanked 474 Times in 281 Posts
    Rep Power
    8

    Default Re: Lever Filler - - How does this work?

    As said above, the nib needs to be completely submerged in the ink. While Jon said to wait 10 seconds, I wait through a slow count to 20.

    Lever fillers are my personal favourites.

  5. The Following User Says Thank You to An old bloke For This Useful Post:

    MTHall720 (September 22nd, 2019)

  6. #4
    Senior Member
    Join Date
    Nov 2016
    Location
    Clinging desperately to planet Earth
    Posts
    474
    Thanks
    36
    Thanked 474 Times in 281 Posts
    Rep Power
    8

    Default Re: Lever Filler - - How does this work?

    I should add that having a few paper towels at hand is advisable. You will need one to wipe the nib and section. You might need another or two for any possible drips or spills.

  7. The Following 2 Users Say Thank You to An old bloke For This Useful Post:

    Jon Szanto (September 22nd, 2019), MTHall720 (September 22nd, 2019)

  8. #5
    Senior Member
    Join Date
    Aug 2019
    Posts
    100
    Thanks
    51
    Thanked 11 Times in 10 Posts
    Rep Power
    5

    Default Re: Lever Filler - - How does this work?

    Thanks for the help with this.

    Sent from my LG-H910 using Tapatalk

  9. #6
    Senior Member FredRydr's Avatar
    Join Date
    Sep 2012
    Location
    Carlisle, Pennsylvania USA
    Posts
    4,903
    Thanks
    1,395
    Thanked 6,379 Times in 2,500 Posts
    Rep Power
    18

    Default Re: Lever Filler - - How does this work?


  10. The Following 2 Users Say Thank You to FredRydr For This Useful Post:

    2manychoices (November 6th, 2019), Jon Szanto (September 22nd, 2019)

  11. #7
    Senior Member Lady Onogaro's Avatar
    Join Date
    Jan 2014
    Location
    Lafayette, LA
    Posts
    2,197
    Thanks
    5,214
    Thanked 1,578 Times in 943 Posts
    Rep Power
    13

    Default Re: Lever Filler - - How does this work?

    Just a word--if it doesn't fill, it may need a new sac (the sac is inside the pen and holds the ink). Most older lever-fillers I have bought second hand needed to have the sac replaced. A good place to send it for this is Danny Fudge at The Write Pen. But there are lots of videos showing you how to do it yourself if you need to do so.
    Lady Onogaro

    "Be yourself--everybody else is already taken." --Oscar Wilde

  12. The Following 2 Users Say Thank You to Lady Onogaro For This Useful Post:

    MTHall720 (October 9th, 2019), SchaumburgSwan (September 22nd, 2019)

  13. #8
    FPG Donor ♕ Chrissy's Avatar
    Join Date
    Dec 2013
    Location
    United Kingdom
    Posts
    11,367
    Thanks
    6,856
    Thanked 10,336 Times in 3,966 Posts
    Rep Power
    24

    Default Re: Lever Filler - - How does this work?

    Quote Originally Posted by Lady Onogaro View Post
    Just a word--if it doesn't fill, it may need a new sac (the sac is inside the pen and holds the ink). Most older lever-fillers I have bought second hand needed to have the sac replaced. A good place to send it for this is Danny Fudge at The Write Pen. But there are lots of videos showing you how to do it yourself if you need to do so.
    My first ever sac replacement was on an Esterbrook. It wasn't too difficult.
    Regards, Chrissy | My Review Blog: inkyfountainpens

  14. The Following User Says Thank You to Chrissy For This Useful Post:

    MTHall720 (October 9th, 2019)

  15. #9
    Senior Member azkid's Avatar
    Join Date
    Mar 2018
    Location
    Colorado, USA
    Posts
    2,016
    Thanks
    3,725
    Thanked 1,703 Times in 822 Posts
    Rep Power
    9

    Default Re: Lever Filler - - How does this work?

    Ditto what Chrissy said.

    Also, don't force the lever. If it seems obstructed by something hard, that is likely the crusty, petrified remains of the old latex sac.

    If nobody mentioned it, you can still find replacement nib units in NOS or like new condition, usually for not a lot of money, at least for the most common types.

    They screw in easily and come in a variety of line widths and shapes. There are the iridium-tipped version (9000-series) and budget steel 'tipped' which wear out much faster. But all are quite decent nibs if in good condition.

  16. The Following User Says Thank You to azkid For This Useful Post:

    MTHall720 (October 9th, 2019)

  17. #10
    Senior Member
    Join Date
    Aug 2019
    Posts
    100
    Thanks
    51
    Thanked 11 Times in 10 Posts
    Rep Power
    5

    Default Re: Lever Filler - - How does this work?

    Thanks all. My pen is now writing very well. Looked like it was a NOS and came in the original. Super light weight and attractive looking. Although I generally don't like fine points I like this pen more than I thought I would. I usually write with broad due to my hands shaking sometimes. The fine points often make the shaking more obvious.

    Sent from my LG-H910 using Tapatalk

  18. #11
    Senior Member pajaro's Avatar
    Join Date
    Aug 2012
    Location
    Tecumseh, MI
    Posts
    1,373
    Thanks
    561
    Thanked 613 Times in 410 Posts
    Rep Power
    13

    Default Re: Lever Filler - - How does this work?

    Most of the fillers are almost self explanatory, as self explanatory as the designers could make them. Not being afraid of breaking them helps. When I was nine I found the lever filler easy to operate. Too bad the brand new pen had a damaged sac. With most of the other filler types the designers have made the part you operate prominent so you will intuitively understand how to work it, so no reason to be afraid of them, although some people are afraid of breaking something. The pen designers wanted you to succeed.

  19. The Following User Says Thank You to pajaro For This Useful Post:

    MTHall720 (October 25th, 2019)

  20. #12
    Senior Member
    Join Date
    Sep 2019
    Location
    US
    Posts
    6,750
    Thanks
    642
    Thanked 897 Times in 689 Posts
    Rep Power
    11

    Default Re: Lever Filler - - How does this work?

    Quote Originally Posted by MTHall720 View Post
    I recently bought a nice looking lever Filler but have never used one. Do you put the nib in the ink and then pull up on the lever?
    Thanks. PSX_20190922_140818~2.jpgPSX_20190922_141006~2.jpgPSX_20190922_141359~2.jpg

    Sent from my LG-H910 using Tapatalk
    According to Esterbrook's original instructions you dip the pen into the ink and lift and close the lever three times. After closing the third time you leave the pen submerged for a few seconds to allow the sac to fill.

    Replacement sacs, j bars, talc, and sac adhesive/shellac are available from Anderson Pens. I've restored 9 pens over the past 6 weeks or so. So many videos are available that restoring these great pens is easy. The most difficult part for me is disassembling the pens for cleaning and replacing old parts. I used Dawn and warm water as a soak. Sometimes it takes a day or so to loosen the nib and nib holder from the main body. Just go slow.

    Also, NOS replacement nibs are available. The deluxe nibs are the ones with the green threaded end. The 9668 is a good medium nib. I got one with the Deluxe SM model recently acquired.

    Good luck on your restorations.

  21. The Following 2 Users Say Thank You to Chuck Naill For This Useful Post:

    MTHall720 (October 25th, 2019), Sailor Kenshin (October 10th, 2019)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •