Page 5 of 5 FirstFirst ... 345
Results 81 to 85 of 85

Thread: Basic ‘must have’ tools for restoration

  1. #81
    Senior Member azkid's Avatar
    Join Date
    Mar 2018
    Location
    Colorado, USA
    Posts
    2,016
    Thanks
    3,725
    Thanked 1,703 Times in 822 Posts
    Rep Power
    9

    Default Re: Basic ‘must have’ tools for restoration

    I use red and white Dialux polishing compound bars for the polishing. I usually don't bother with green. My goal is usually to reduce the haze of small scratches rather than trying to get to a like new high polish. Just enough to make it look nicer from a distance.

    I am not sure what to say about bad bite marks. I would be inclined towards 400 then 600 grit sandpaper then zona paper from 30 micron to 1 micron then polish with white. I've only had to deal with shallow teeth marks so far.
    Last edited by azkid; July 25th, 2020 at 10:29 PM.

  2. The Following User Says Thank You to azkid For This Useful Post:

    Chrissy (July 25th, 2020)

  3. #82
    Senior Member
    Join Date
    Jun 2012
    Posts
    481
    Thanks
    2,479
    Thanked 243 Times in 136 Posts
    Rep Power
    12

    Default Re: Basic ‘must have’ tools for restoration

    Interesting thread. For anyone wanting to get some help with learning how to restore pens, I found the Writing Equipment Society course very helpful.

    I have found that getting knowledge about vintage pens and restoring/repairing them has significantly increased my appreciation of such pens, and even basic repairs like sac replacement generate a huge amount of satisfaction, using only basic tools as described.

    One big challenge I have always found is with the metal parts. Clips, other trim, and caps. Sometime an ammonia solution, polish and elbow grease can help clean up a clip in poor condition but brassing, pitting and loss of plating is something that I don’t think can be fixed, at least not with any basic equipment but I would be happy to be corrected or receive suggestions on how it could be done?

  4. #83
    FPG Donor ♕ Chrissy's Avatar
    Join Date
    Dec 2013
    Location
    United Kingdom
    Posts
    11,367
    Thanks
    6,856
    Thanked 10,336 Times in 3,966 Posts
    Rep Power
    24

    Default Re: Basic ‘must have’ tools for restoration

    Quote Originally Posted by da vinci View Post
    One big challenge I have always found is with the metal parts. Clips, other trim, and caps. Sometime an ammonia solution, polish and elbow grease can help clean up a clip in poor condition but brassing, pitting and loss of plating is something that I don’t think can be fixed, at least not with any basic equipment but I would be happy to be corrected or receive suggestions on how it could be done?
    You're correct in that metal parts can look better after a polish, but pitting and/or loss of plating can't be fixed using basic tools. In order to restore plated metal parts the only perfect method would be replating and that's something that needs a different sort of expertise and non-basic tools.

    You would need to a) remove the parts from the pen or cap and b) remove all of the old pitted or old worn off bits of plating so that the part to be plated is pristinely clean. Then you would need to replate it using a specialised replating solution in gold or silver or platinum with an electroplating machine. it's not cheap to get the machines or the precious metal chemicals. Nor is it cheap to get the job done by those people who have the specialist kit.
    Regards, Chrissy | My Review Blog: inkyfountainpens

  5. The Following User Says Thank You to Chrissy For This Useful Post:

    da vinci (July 26th, 2020)

  6. #84
    Senior Member
    Join Date
    Jun 2012
    Posts
    481
    Thanks
    2,479
    Thanked 243 Times in 136 Posts
    Rep Power
    12

    Default Re: Basic ‘must have’ tools for restoration

    Quote Originally Posted by Chrissy View Post
    Quote Originally Posted by da vinci View Post
    One big challenge I have always found is with the metal parts. Clips, other trim, and caps. Sometime an ammonia solution, polish and elbow grease can help clean up a clip in poor condition but brassing, pitting and loss of plating is something that I don’t think can be fixed, at least not with any basic equipment but I would be happy to be corrected or receive suggestions on how it could be done?
    You're correct in that metal parts can look better after a polish, but pitting and/or loss of plating can't be fixed using basic tools. In order to restore plated metal parts the only perfect method would be replating and that's something that needs a different sort of expertise and non-basic tools.

    You would need to a) remove the parts from the pen or cap and b) remove all of the old pitted or old worn off bits of plating so that the part to be plated is pristinely clean. Then you would need to replate it using a specialised replating solution in gold or silver or platinum with an electroplating machine. it's not cheap to get the machines or the precious metal chemicals. Nor is it cheap to get the job done by those people who have the specialist kit.
    Thanks Chrissy, that’s what I thought. I just need to buy better condition pens! 😂

  7. #85
    Senior Member Johnny_S's Avatar
    Join Date
    Apr 2020
    Posts
    112
    Thanks
    31
    Thanked 73 Times in 46 Posts
    Rep Power
    4

    Default Re: Basic ‘must have’ tools for restoration

    PM sent

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •