Results 1 to 8 of 8

Thread: Vintage Tibaldi 20-L - Piston needs new cork

  1. #1
    Member
    Join Date
    Dec 2020
    Posts
    63
    Thanks
    1
    Thanked 13 Times in 11 Posts
    Rep Power
    1

    Default Vintage Tibaldi 20-L - Piston needs new cork

    In a previous post I said I bought this vintage pen. I have to remove the piston assembly to see if and how I can replace the cork seal or maybe use an o-ring.
    In my opinion the piston mechanism is inserted like the Parker Vacumatic button filler. The blind cap screws on to a protruding threaded bit that, I can see, is threaded inside the barrel. How to remove this though is a mistery. Shall I put the barrel in the ultrasonic cleaner and see what happens after a few cicles? Shall I find a tool similar to that of the Vacumatic to try and unscrew the end bit? The pen is clean, I have removed the screwed in section, I can see the piston going up and down but water/smoke comes out at the back. Definitely a new seal is needed. Other suggestions? Thank you. Marco

  2. #2
    Senior Member fountainpenkid's Avatar
    Join Date
    Feb 2011
    Location
    Nouvelle Angleterre
    Posts
    3,505
    Thanks
    3,149
    Thanked 1,051 Times in 526 Posts
    Rep Power
    14

    Default Re: Vintage Tibaldi 20-L - Piston needs new cork

    Do you have a way to precisely measure the blind cap thread diameter? If so, you could see if one of the vacumatic filler tools might work (https://www.etsy.com/listing/7796499...BoCA0IQAvD_BwE).
    Will
    If my p.m box is full, feel free to email me at dabantur@gmail.com.

  3. #3
    Member
    Join Date
    Dec 2020
    Posts
    63
    Thanks
    1
    Thanked 13 Times in 11 Posts
    Rep Power
    1

    Default Re: Vintage Tibaldi 20-L - Piston needs new cork

    The references I found on this pen model say that the pen is a button filler. Found a picture on the internet and indeed it has a button filler system. Mine has a piston. Which is which ?
    I tried the Parker Vacumatic tool I have and it is too small. I measured the diameter of the screw and will have to look for a nut of that size. In the meantime I've given the barrell about 6 rounds in the ultrasonic cleaner, the piston system doesn't budge.
    I wrote present day Tibaldi asking for info, no reply.
    Last edited by MarcoA64; October 9th, 2021 at 03:01 PM. Reason: incomplete post

  4. #4
    Member
    Join Date
    Dec 2020
    Posts
    63
    Thanks
    1
    Thanked 13 Times in 11 Posts
    Rep Power
    1

    Default Re: Vintage Tibaldi 20-L - Piston needs new cork

    Good news at last! I removed the piston assembly.
    A bit of heat from a hair dryer and a plier helped me unscrew the assembly and here you can see how it is made:

    Piston groove.jpg

    The knob had been already 'mishandled' prior to me working on it.

    I am thinking of using an o-ring where the groove is highlighted as I don't think I can find the whole 'groovy' bit anymore.

    I have cleaned the grooves of the piston assembly screw and will use silicon grease to reassemble it and the section hoping the o-ring does its job.

    This is what the, disassembled, pen looks like:

    Disassembled Tibaldi.JPG

    The flashed photo doesn't do it justice but it is, I believe, green and striated silver.

    The pen is all plastic, IMO.

    Ciao - Marco

  5. The Following User Says Thank You to MarcoA64 For This Useful Post:

    fountainpenkid (October 12th, 2021)

  6. #5
    Member
    Join Date
    Dec 2020
    Posts
    63
    Thanks
    1
    Thanked 13 Times in 11 Posts
    Rep Power
    1

    Default Re: Vintage Tibaldi 20-L - Piston needs new cork

    The o-rings I have found in a shop are too thick. Where do you suggest I look for them online in UK ?

  7. #6
    Member
    Join Date
    May 2012
    Location
    Belgium
    Posts
    45
    Thanks
    3
    Thanked 127 Times in 29 Posts
    Rep Power
    0

    Default Re: Vintage Tibaldi 20-L - Piston needs new cork

    Could be wrong, but I expect there never has been an O ring in the groove....
    I think the part with the groove is the piston seal itself.
    Does the part fit with a slight radial pretension in there barrel bore?
    Francis

  8. #7
    Member
    Join Date
    Dec 2020
    Posts
    63
    Thanks
    1
    Thanked 13 Times in 11 Posts
    Rep Power
    1

    Default Re: Vintage Tibaldi 20-L - Piston needs new cork

    Hi Fountainbel, I agree with you. But the piece with the groove has hardened and it is not air tight anymore. I thought of using an o-ring just to get it air tight again. Water exists from the blind cap and also smoke, which I blew into the barrel :-)
    Marco

  9. #8
    Member
    Join Date
    Dec 2020
    Posts
    63
    Thanks
    1
    Thanked 13 Times in 11 Posts
    Rep Power
    1

    Default Re: Vintage Tibaldi 20-L - Piston needs new cork

    The set of silicone o-rings I have ordered has arrived.
    The o-rings have Internal Diameter = 6 mm and Cross Section = 1 mm
    The piston head has a diameter of 8+ mm.
    I
    assumed that if I got a smaller o-ring by putting it in the groove it would stretch and possibly reduce the Cross Section a bit more.
    The grove on the head is smaller than 1 mm as this o-ring sticks out a bit.

    I mounted the o-ring, spread some silicon grease on it and inserted it into the barrell, it goes up and down very smoothly.
    I sucked in some water and then some ink and the barrell fills as emptying it the liquid comes out, something that didn't happen before.

    Unfortunately it writes while the feed is wet, after filling the pen, but then it dries out.
    I had pushed water through the section and it flowed perfectly so can't think of where the blockage is.

    Something else to investigate now.
    Have a nice week end
    Marco

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •