-
May 24th, 2018, 10:56 AM
#901
Senior Member
- Rep Power
- 12
Re: Pen cases
Hi Wuddus
Thanks for taking the time to comment and share your ideas it is very much appreciated.
I had neglected to mention that the little wooden toggle that closes the case is also a pen rest I did not take any pictures of this one in fact I had to go back some time to find a picture.
DSC_0090[1] by my0771, on Flickr
Michael
-
The Following 2 Users Say Thank You to MY63 For This Useful Post:
NibsForScript (June 24th, 2018), Wuddus (May 24th, 2018)
-
May 24th, 2018, 12:28 PM
#902
Senior Member
- Rep Power
- 9
Re: Pen cases
Using the toggle as a pen rest is ingenious!
-
The Following User Says Thank You to azkid For This Useful Post:
-
November 8th, 2018, 09:39 AM
#903
Senior Member
- Rep Power
- 12
Re: Pen cases
It has been a little while since I shared anything here life has a way of taking over at times.
My current pen case is for three Emperor size pens.
The inside liner is made from Kydex for strength which is wrapped in suede.
2018-11-08_04-10-10 by my0771, on Flickr
2018-11-08_04-10-52 by my0771, on Flickr
2018-11-08_04-11-11 by my0771, on Flickr
Once all three pen tubes are wrapped in suede I started thinking about the outer cover. This is made from 3 mm veg tanned leather which is wet formed in a wooden mould.
This picture shows the piece of leather in the mould as I started to apply pressure from the clamps.
2018-11-08_04-11-48 by my0771, on Flickr
Here you can see the leather has been forced into the shape of the mould.
2018-11-08_04-12-03 by my0771, on Flickr
2018-11-08_04-12-29 by my0771, on Flickr
After drying for a few hours I removed the front from the mould.
2018-11-08_04-12-50 by my0771, on Flickr
When I was happy that everything fitted together I applied the dye. I allowed the flap to dry in its closed position to prevent cracking and graining when opened and closed.
2018-11-08_04-13-16 by my0771, on Flickr
This is a dry fit of all of the pieces
2018-11-08_04-14-14 by my0771, on Flickr
Stitching in progress
2018-11-08_04-14-49 by my0771, on Flickr
Once the closing strap was in place I stopped stitching and started working on the flap template.
2018-11-08_04-14-49 by my0771, on Flickr
2018-11-08_04-15-05 by my0771, on Flickr
Using my circle tool I rounded the corners this is where I am at this time I am thinking that the point where the shape starts needs to be closer to the inside of the case.
2018-11-08_04-15-36 by my0771, on Flickr
Thanks
Michael
-
The Following User Says Thank You to MY63 For This Useful Post:
azkid (November 9th, 2018)
-
November 9th, 2018, 04:12 PM
#904
Senior Member
- Rep Power
- 12
-
The Following User Says Thank You to MY63 For This Useful Post:
NibsForScript (November 11th, 2018)
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Bookmarks